BOCA RESEARCH, INC. BOCA 112K DYNAMICDUO Card Type Modem, Fax Chip Set Unidentified Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.22A/B, V.23, V.32, V.32bis, V.34 Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29, V.33 Error Correction/Compression MNP10-EC, MNP5, V.42, V.42bis Fax Class Class I Data Bus 32-bit PCI Card Size Three-quarter length, full-height card [Image] CONNECTIONS Function Label Function Label Line in CN1 Line out CN2 SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, H, M, O, Q, V, W, X, Y, Z &C, &P, &T, &V, &W, &Y Extended AT Commands \K, \N %C, %E, %L, %Q S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S82, S91, S92, S95 Special Commands +MS Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 Auto-mode detection enabled COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects communications mode options Command Mode &Q0 Asynchronous mode, serial port speed follows connect speed. &Q5 Error correction mode &Q6 Buffered asynchronous mode DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q &Q Setting &D0 &D1 &D2 &D3 &Q0, &Q5, &Q6 NONE Command 2 Command 3 Command 4 &Q1, &Q4 Command 1 Command 2 Command 3 Command 4 &Q2, &Q4 Command 3 Command 3 Command 3 Command 3 Command Function Command 0 Modem does not respond to DTR Command 1 Modem goes to command mode after DTR goes is off Command 2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. Command 3 Modem is initialized after DTR goes off DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D^ Disable calling tone D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Restore factory configuration 0 &F1 Restore factory configuration 1 FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled &K5 Transparent XON/XOFF flow control enabled &K6 Both RTS/CTS and XON/XOFF flow control enabled REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports the product identification code I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Reports the firmware revision level I4 Reports OEM defined identifier string I5 Reports country code I6 Reports modem data pump model I7 Reports DAA code RTS/CTS Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Selects RTS/CTS options Command Function &R0 Function not supported &R1 CTS forced high, RTS is ignored. SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting STORE TELEPHONE NUMBER Type: Configuration Format: AT [cmds] &Zn=(phone # & modifiers) Description: Writes selected telephone numbers into the non-volatile memory at location n Note: The characters described in the D command are valid for use in the &Z command; telephone numbers and modifiers can include up to 36 characters. Command Function &Z0 Stores a 34 digit dial string &Z1 Stores a 34 digit dial string &Z2 Stores a 34 digit dial string &Z3 Stores a 34 digit dial string Extended AT Commands SINGLE LINE CONNECT MESSAGE Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects the operating mode the modem uses while connected Command Function \V0 Connect messages are controlled by the command settings X, W, and S95 \V1 Connect messages are displayed in single line format S(status) -REGISTERS AUTOSYNC OPTIONS Type: Register Format AT [cmds] S19=n [cmds] Default: 0 Range: 0-255 Unit: 1 second Description: Sets the AutoSync options CONNECTION FAILURE CODES Type: Register Format AT [cmds] S86? [cmds] Description: Reports codes which correspond to the possible causes of a connection failure Value Meaning 0 Normal hang up 4 Carrier signal lost 5 No error-control detected for remote modem during feature negotiation 9 No common protocol found 12 No failure - remote modem disconnected normally 13 Remote modem failed to respond after 10 re-transmissions same message 14 Violation of negotiated protocol caused failure DATA COMPRESSION CONTROL Type: Register Format AT [cmds] S46 [cmds] Default: 128 Range: 128 Description: Controls data compression HDLC ADDRESS Type: Register Format AT [cmds] S20=n [cmds] Default: 0 Range: 0-255 Unit: 1 second Description: Sets the AutoSync HDLC address V.42 NEGOTIATION Type: Register Format AT [cmds] S48 [cmds] Default: 7 Range: 0, 7, 128 Description: Controls V.42 negotiation